The Archive · 1902

A New Shallow Draught Steamer

(From the Times? of the 20th A new type of shallow draught screw steamer, which has been designed by Messrs. Yarrow and Ca., of Poplar, yesterday ran a preliminary trial trip on the Thames. The vessel has been built for trading purposes on South American, rivers where shallow draught is an essential feature in the navigation. She is Zaft. long by 92ft. wide, and will carry, when fully loaded, 20 tons. The machinery is of the usual type so far as the engines and boilers are concerned. The propeller, howerer, is so placed that with a diameter of 2}ft. it can be fully immersed when the boat is drawing no more than Llin., and that without its projecting below the hot-tom. It may be stated that Messrs. Yarrow have already constructed several small steam,>s, both for war purposes and for trading, in which the diameter of the screw ix considerably greater than the draught of the boat. It will make the description clearer, perhaps, if we describe the older method before dealing with the latest arrangement. In the vessels previously constructed the after part of the bottom, or "run," is made very flat, as it must necessarily be in shallow draught craft. The central part of the bottom plating is arched up so as to form a tunnel in the after part of the vessel. This tunnel is not only arched in cross section, bnt also in longitudinal section, its highest point rising considerably above the normal water plane at which the boat floats. In this tunnel the scream revolves, the propeller shaft going through a stuffing-box in the plating much in the usual way. Tt will therefore be scon that the summit of the tunnel, being abore the water level. is filled with air. and the upper part of the propeller. probably two-thirds, is out of water. The entrance to the tunnel and the exit astern are below the water level, as also are the sides. A. screw not completely immersed is a most inefficient instrument of propulsion, but in the tunnel boats the propeller drives out the air from the crown of the tunnel as soon as it begins to revolve, and the pressure of the atmosphere on the surface of the surrounding sea drives water up to fill the vacuum thus formed. In this way, so long as the vessel is going, the screw is completely submerged and' works with maximum efficiency, being in solid water. It may be added that in most screw vessels, excepting those of very deep draught, there is a tendency on the part of the propeller to draw down air, and this often leads to a serious loss of power. In th case of vessels of the type described (ho steel plating of the tunnel which almost surrounds the se few prevents this undesirable action.

In order to reach the end described, it should be remembered, the bottom edges of the tunnel must be beneath the normal water plane; otherwise the vacuum would not be formed, and the water would not rise to cover the propeller. This, however, leads to a serious drawback in the sys tem, The propeller race, or water sent aft by the screw, is largely thrown against the downward sloping after part of the turnel; and, though the latter is eased off to as flat an anglo as possible, this deflection of the race naturally absorbs a great deal of power. This is more especially the case when a vessel is loaded for, naturally, the boat must be designed for the edges of her tunnel to be immersed even when she is at her lightest draught. It is in order to overcome this defect that Messrs, Yarrow have invented the new arrangement of tunnel which is the distive feature of the boat tried yester day. Tu place of the tunnel dipping down in as it. goes aft, after reaching the greatest height, it is carried along witl" the top of the arch parallel with the water level. The exit astern is therefore above the water level, so that. air would be admitted, thus vitiating the principle, were not special means taken to prevent it. Aft of the propeller is a hinged flap or shutter made of plate steel. This is so arranged that it hinges on the roof of the tunnel, its forward end—where it hinges—being just aft of the propeller. When this flap' is lowered its after end dips under water, and it thus forms an after downward inclined roof to the tunnel and enables the vacumn to be formed and the water lifted when the screw revolves in the manner already described. Tt should be stated that the tunnel is made of rectangular section where the flan is.

By this ingenious device Messrs. Yarrow have overcome the one great objec tion to the tunnel-enclosed method of screw propulsion, which, in spite of the drawback to which reference has been made, has been found to possess great advantages for shallow water service, Up to recent times it has been considered that paddle-wheel steamers were necessary for such purposes, because immersion centd not be obtained for the screw. With side-wheel steamers the extra width needed was often a serious objection in now countries and narrow channels. The stern-wheel arrangement overcomes this difficulty, but in all paddle-wheel vessels the machinery is both expensive and heavy, and its weight presents another serious difficulty when light draught is a necessary feature, A screw engine will make two or three revolutions to one of a paddle steamer, and with equal power developed would be very much lighter. At varying draughts the paddle-wheel with radial floats is a very inefficient instramen: that is to say, it is efficient only at the draught for which it is designed: and when feathering floats are used the cost of upkeep is greatly augmented, owing to the wearing of bushes and joints. Tu some waters the upkeep of the feathering pad-

Text read from the printed page and cleaned; old type leaves the occasional error.

Your account